DESCRIPTION
PHOTO (click for larger image)
PRICE
single groove race valves
valve sizes 34/30mm
shims/springs/bases/valves/followers
& cottors
Kit includes
flywheel/clutch/drive plates & bearing
Need Hyd AP cyl
30 inlet 34 ex 6mm stems
to run with no advance mechanism
Pulleys not included
kit includes steel crank/steel rods/forged high comp pistons and Cosworth bearings
for std crank pins sizes and AHM pin sizes to suit AHM steel crank with Cosworth crank pins
SET
2.0 l 16v twinspark forged pistons 83mm/83.5 and 84mm bore sizes 12 to 1 cr
SET
race 48mm Tapered bodies
DESCRIPTION
PHOTO (click for larger image)
PRICE
kit includes
valves/springs/bases/caps/cotters/followers & shims
Sizes 34mm in 30mm ex or 36mm in 30mm ex
Convert you 16v engine to solid tappets for higher revs as std hydraulic tappets can fail
Kit is for std valve lengths and std cam base circles,shims come over sized so need to be sized to suit
Average shim size is approx 3.0mm Shims supplied at 5.0mm
Can be use with std hydraulic lifters
Cams can be supplied in varies profiles and lift in hydraulic spec if required
Race inlet and ex 322 degs 11.48mm lift 51/81
Race inlet 320 degs 11.20mm lift 52.6/87.4 ex 315 degs 11.07mm lift 91/44
other profiles available
prices for head work are plus parts
ie valve guides, valves etc
£1500.00
kit includes steel crank/steel rods/forged high comp pistons and bearings
block not inc
for AHM flywheel and clutch set up
Parts included
flywheel/clutch/drive plates & bearing
Ring gear not included
and AHM camshafts
£450.00
2.0 EXTRA £10 PER ROD
£940 SET
STD BOXER 1.7/1.5/16V CON ROD FITTED WITH UPDATED BOLTS
Send your cleaned rods for use to modify
12 to cr
AHM
AHM 2.0 L Kit for boxer engs
includes forged pistons,steel h sec rods and steel crank
Cyl block needs some mods for this kit
Block not included
Std 60mm dia and 62mm dia for faced blocks and heads with uprated bearings set of 4
DESCRIPTION
PHOTO (click for larger image)
PRICE
This is the very first conversion that we fitted our Inlet manifold designed and made for AHM no matter what you read else where thats why they have our name in the casting .
Giulia Super fitted with 45mm throttle bodies running a Omex fuel and ignition 3D system with around 180 bhp,and much better low speed drivability and idle compared to carbs.
As you can see both set ups are very neat coil packs can be mounted in side the car as seen here to give a real clean look.
These systems can be fitted and mapped here on our rolling road.
Made for 105 T/Spark conversions designed and tested by AHM fitted to the first AHM t spark
This lovely manifold bolts straight on to a std 2.0 Twin spark Alfa 75 engines and early 164 engines and can be fitted into 105 series cars.
Temp gauge hole threaded for std 105 sender unit and bosses at the back to be added if required for heater and brake servo.
105 8 VALVE TWIN SPARK CARBURETTOR AND 3D OMEX 200 ECU SETUP KIT
Kit includes parts shown plus coil packs,ing amps, wiring loom ,plugs ,throttle pot ,air filter and plug leads that can be cut to length to suit you, plus software ,coms lead and a start up maps ,every thing needed to fit and run your engine all you need is a laptop with windows 98/2000
Then over the phone we can help you with the software and set up the basic parameters unlike others who just re box and sell when they have never fitted or set it up
Final mapping should be done by us or a rolling road of your choice . Mapping on the road can give very good results as well
prices on Webbers can vary as they are becoming very rare now
45 DCOE £270.00 each
48 DCOE £ POA each
Please state 45mm or 48mm carbs
£440.00 MANIFOLD AND FULL SYSTEM
Kit includes
AHM FORGED PISTONS HIGH COMP
SET OF LINERS
BIG END BEARINGS (please state if under size)
AHM INLET MANIFOLD AND MOUNTINGS
AHM STEEL CAMSHAFTS AND FOLLOWERS
AHM VALVE SPRING SET
THROTTLE BODYS 45MM SET
HI FLOW INJECTORS
FUEL PRESSURE REGULATOR
AIR FILTER AND BASE PLATE
AHM DIS ECU COILS AMPS LOOM THROTTLE POT WITH START UP MAPS
These new OMEX 200 ecus have out puts to run shift lights and fuel pumps plus are modified for this conversion to run 2 coils packs for 8 plugs
PLUG LEAD KIT TO MOUNT COILS IN CAR IF REQUIRED
GASKET SET
DIZZY AND ADVANCE MEC BLANKING PLUG SET
UPRATED CON ROD BOLTS
Ex system not included
Kit includes
AHM FORGED PISTONS HIGH COMP
SET OF LINERS
BIG END BEARINGS (please state if under size)
AHM INLET MANIFOLD AND MOUNTINGS
AHM STEEL CAMSHAFTS AND FOLLOWERS
AHM VALVE SPRING SET
45MM CARBURETTORS
AIR FILTER AND BASE PLATE
AHM DIS ECU COILS AMPS LOOM THROTTLE POT WITH START UP MAPS
These new OMEX 200 ecus have out puts to run shift lights and fuel pumps plus are modified for this conversion to run 2 coils packs for 8 plugs
PLUG LEAD KIT TO MOUNT COILS IN CAR IF REQUIRED
GASKET SET
DIZZY AND ADVANCE MEC BLANKING PLUG SET
UPRATED CON ROD BOLTS
Ex system not included
std valve set up work well with AHM
camshafts below
Modified OMEX 200 ECU for T Spark set up uni loom, throttle potentiometer, ignition amps coil packs,mini timer plugs, software and coms lead etc
This great ECU has 3 out puts for shift light ,rev counter and fuel pump unlike the old 100 ecus
We can give help and advice as we supply and map Omex ecus all the time not just rebox and sell.
Kit will be supplied with a start up map plus maps we have done can be emailed to you if required
OMEX 200 ECU KIT FOR CARBS
KIT FITTED TO 105
Throttle bodie kit Using Omex 600 FUEL AND IGN ECU
THROTTLE BODY KIT FITTED TO 105
AHM T.S 300 Fast road 318 degs 11.30mm lift 55/83
Cams above work very well in fast road cars with 45mm carbs or throttle bodies
RACE 1 IN 315 degs 86/50 13mm lift EX 317 degs 54.6/83.2 12.77mm lift
RACE 2 IN 308 degs 48/78 11.22mm IN and EX
Made from steel blanks
DESCRIPTION
PHOTO (click for larger image)
PRICE
AHM 2.0 AND 2.1 TWIN CAM 105 RACE ENGINE PARTS
£940 SET
kit includes
valves/springs /bases/caps/cottors/guides/followers & shims
Other sizes made to order with std pin sizes
RACE 1 IN 315 degs 86/50 13mm lift EX 317 degs 54.6/83.2 12.77mm lift
RACE 2 IN 308 degs 48/78 11.22mm IN and EX
Made from steel blanks
also for 1600 and 2000. 84.75mm for 2.0 classes
This stops the liners moving at high revs and allows bigger bore sizes over std single liners.
*Block requires modifying to suit
Available for both large & small splined halfshafts.
DESCRIPTION
PHOTO (click for larger image)
PRICE
Crank has oil ways drilled to our designs for better lubrication and crank pins are made to Cosworth sizes so we can use uprated bearings
Rods are longer to give less angle with pistons to suit
Pistons have 20mm pins to keep the weight down
for use with AHM long rods
Pistons made for std rod lengths and std pin diameters
Bore sizes 78/78.5mm
RACE 311 deg 12.60mm lift
kit includes
valves/springs/bases/caps/cottors/guides/followers & shims
Available for both large & small splined halfshafts.
DESCRIPTION
PHOTO (click for larger image)
PRICE
£170.00 Fibreglass
AHM splitter carbon or f/glass
Bumper
Carbon
£450.00
Fibreglass
£350.00
splitter
£150 Carbon
£100
Fibreglass
BONNET HAS TO BE MOUNTED WITH PINS
Fibreglass £180.00
Carbon
£230.00
This boot lid has fixings for std hinges and catch if used for std cars
Carbon
£200.00
Fibreglass
£150.00
DESCRIPTION
PHOTO (click for larger image)
PRICE
fully mappable engine management system
Fully made up loom replaces old motronic set up and allows removal of restrictive air flow meter , idle valve , cold start injector and distributor
Connects up to std crank sensor on front pulley with 60-2 pattern on motronic engines only
Early engines had distributor triggered ecus ie no crank sensor on front pulley you will need to add at 60-2 trigger wheel and sensor or find a s hand front pulley etc of a motronic car
Kit includes most parts to run the eng inc at start up map from cars we have done
You will need to make new plug leads or use the std ones and fit new ends to suit Dis coil pack
Kit includes
Omex 710 ecu ,Throttle pot ,Coil pack ,Wiring loom Air filter, Distributor Blanking plate and drive Air temp sensor
This kit will also fit 24 valve engines fitted in SZ,75,GTV6s and can be used with std plenum or AHM throttle body kit
GTV6,SZ,ALFA 75 EMS KIT
3.5 ALFA 75
£1499.00
Fitted and mapped
£2499.00
ENGS RUNNING D.I.S ING systems
This neat cover has bearing and shaft to hold the oil pump drive down when distributor is removed for EMS using no distributor
AHMotorsports are pleased to announce, after months of development work, we can convert your 3.0 Litre 12 or 24 valve block to accept liners and pistons to increase the capacity to 3300cc /3500cc/3800. The kit comprises of:
-
Set of 6 101mm liners
-
Set of 6 Seal Rings
-
Set of six pistons (with Piston Rings)
-
2 head gaskets
-
3.8cc kits comes with crankshaft
-
3.3/3.5cc Price £2,000+vat (kit only)
-
3.8cc £2,700+ vat
Block will need to be modified to suit the new liners
12V 3.5 kit shown for SZ
BLOCK NOT INCLUDED
complete conversions car be carried out please e mail for a quote
3.8 Kit price £2700.00
AHM can convert your 3.0 GTV or 3.2 GTA 24 valve block to accept liners and pistons to increase the capacity to 3500cc or 3800cc The kit comprises of:
-
Set of 6 101mm liners
-
Set of 6 Seal Rings
-
Set of six forged pistons (with Piston Rings)
-
2 head gaskets
-
3.8cc for 3.2 engines £2,000 + vat (kit only)
Block will need to be modified to suit the new liners
24v 3.8 kit shown for 147/156 GTA 3.2 etc
BLOCK NOT INCLUDED
complete conversions car be carried out please e mail for a quote
£2000.00
Set of 6
Set of 6
FOR 11 to 1 CR WITH STD HEAD VOLS
Set of 6
inc 3.2 GTA
set 6
Pic above 12V 3.5 SZ fitted with AHM throttle bodies
£285.00 set
AHM V6 THROTTLE BODY KIT 24V AND 12V
Kit is available with Motec or Omex E.C.U 12/24v
Also Available with Carbon Trumpets for some applications and different lengths 45x45 45x65 45x90
Kit Includes inlet manifolds/air horns/fuel rails -6/45mm t bodies linkages fuel rail mountings throttle pot
Injectors not included
Kit
Reprofiled we will need your std cams in exchange
Reprofiled £350.00
Can be use with std hydraulic lifters
Convert you 24v engine to solid tappets for higher revs as std hydraulic tappets can fail
Kit is for std valve lengths and std cam base circles,shims come over sized so need to be sized to suit
Average shim size is approx 3.0mm Shims supplied at 5.0mm
kit includes cam followers, shims
£576.00
DESCRIPTION
PHOTO (click for larger image)
PRICE
kit includes
valves/springs/bases/caps/cottors
followers & shims
std valve set up mec (camshafts only)
OR 2.0L
2.0L PLUS £10 PER ROD
£940 SET
Parts include
flywheel/clutch/drive plates & bearing
flywheel and clutch set up
pair
kit includes steel crank/steel rods/forged high comp pistons and bearings
Block not included
Stops the seals popping out when heads fill with oil on cornering. Much neater then 2 big washers
